Exactly How to Remove and Change a Tub.
Exactly How to Remove and Change a Tub.
Blog Article
They are making a number of good observations about How to Install a Bathtub Yourself as a whole in the article down the page.
Installing a tub isn't precisely brain surgery, but it does require solid plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably hard task. If the old bathtub is readily available, the project can move immediately; if you have to open up a wall surface to get rid of the old bathtub and also place the brand-new bathtub, the task is much harder. In either case, the project is within a home handyman's skills, although you will need a helper to leave the old tub as well as set in the new one. Make certain you have qualified yourself for the task as well as are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed job, it is much better to think about employing one before you begin. Chances are you may require a specialist plumber to make tube links.
This post will certainly assist you set up a new bathtub in your bathroom if you have currently acquired a brand-new bathtub as well as don't need to transform the plan of your previous water system pipes.
Your tools and material list need to make up the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you should do is disconnect the water. After doing so, switch on the taps to drain any kind of water staying in the system. The process of removing the existing faucets can be rather problematic due to the limited gain access to that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. When the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic connector to prevent damage to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end supplies a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the installing opening in the bath/basin ensuring that the washing machines remain in location in between the tap as well as the sink. Safeguard the tap in position with the producer given backnut. When the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap ports. The previous type ought to be linked to the faucet finishes initially, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Utilizing both wood boards under its feet, place the tub in the called for placement. The wooden boards are practical in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four small points.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the bathtub up until the level reviews degree.
To mount taps, fit the bottom of the furthest versatile faucet adapter to the ideal supply pipeline by making a compression join; then do the same for the other tap.
Turn on the water and also check all joints and new pipework for leaks and tighten them if necessary. Load the tub and also check the overflow outlet as well as the typical outlet for leaks.
Lastly, take care of the bathroom paneling as explained in the maker's user's manual. Tiling as well as securing around the tub must wait up until the tub has been utilized a minimum of once as this will settle it into its last placement.
Planning for the Installment
To start with, the sustaining framework supplied with the bath should be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps device to prevent stress on the tub.
Fit the flexible faucet adapters to the bottom of both taps using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should currently be ready to be suited its final position.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to break a rigid seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, causing complications with wetness and feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components and installations. They are sold in tubes as well as cartridges, and are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the bath tub with water before sealing, to permit the movement experienced when the tub remains in use. The sealant can fracture fairly early if you do not take into account this movement before securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly readily available on the market. It is a good idea to fit the floor tiles using water-resistant or water-proof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading about How to Install a Bathtub? Try leaving a remark down below. We will be interested to see your thinking about this post. In hopes that you come back again soon. Those who enjoyed our blog entry please remember to pass it around. I value reading our article about How to Install a Bathtub Yourself.
Schedule Today! Report this page